Monday, February 23, 2015

Special Units

Many of us have had wargame units that have performed exceptionally compared to others in the same army.   Sometimes better than usual and sometimes worse than usual.  

Years ago when I got started with ancients using WRG IV, I fielded a Seleucid army.  At first it included some 20mm Airfix Romans and some 20mm metal phalangites.  IIRC the manufacturer was Brescia.  At the time I was told that the Seleucids did not have Roman type infantry.  Years later it was found that they did.  One of the units in the army  was a fifty figure formation of levy archers.  The worst class of troops possible under the rules.   They usually occupied a hill behind the main line of the army and would turn any unit that came in range into a pin cushion.  Their morale never faltered.  One time a friend and I played a Jewish revolt game.  My friend took the Seleucids and I had the Jews.  It may have been the first turn of the game or possibly the second, when the levy archers had to take a morale test.  The result was an uncontrolled advance towards my army.  They came in range of my archers, took some casualties, had to perform another morale test, and broke, fleeing off the field.

Some years later I ran an American Civil War campaign at the local hobby shop.  It was a fictional campaign between the Empire (Union) and the Federation (Confederates).  Star Wars had recently been in the theaters %).   Commanders had names like J.B.T. Hutt or D. Vader.  During one of the early battles a Confederate infantry brigade performed outstanding acts of valor, throwing back attacks by Union troops though greatly outnumbered.  They became known as the St. John's Brigade due to their flag.  Every time they were involved in a battle they continued to out perform all others.  The Union players came to fear them and whenever there was a battle they would immediately try and locate the brigade.   The St. John's brigade had started the campaign with 1500 men and over the course of the campaign they had eventually been reduced to less than 500 men.  In their final battle the Union surrounded them with over three times their number and fired several volleys into them.  There were few survivors.  At this point the Empire had conquered most of the Federation and the campaign drew to a close.

Sunday, February 22, 2015

Hoplites

A while back I purchased some figures from Rapier Miniatures to round out the hoplites for the battle of Nemea.   Unfortunately some of the figures had miscast shields.  I emailed Rapier about this and received a response that they would "get on it right away".  Since I had always had good service from them I thought nothing further of it and went on to other projects.  This past weekend I returned to the hoplites and realized that I had heard nothing further from Rapier. 
 
Since I had acquired a number of larger scale shield designs I experimented with reducing them to fit the 6mm figures.  The program I used is Paintshop Pro 7.  This program allows you to increase the number of pixels per inch when you reduce an image keeping the detail.  Microsoft Paint will not allow you to do this and has a maximum of 96 pixels per inch.   After some experimenting I found that if I reduced them by a factor of six and increased the number of pixels per inch by the same factor that the size was just about right for the figures.  I printed them on heavy white cardstock.  I trimmed the remains of the shields from the figures and used white glue to attach the shields after cutting them out.  Cutting circles less than 4mm in diameter is a bit difficult.  I may check with some of the craft stores and see if it is possible to obtain a hole punch that is the correct size as I have about five dozen more to cut and glue.  The following images show the first dozen figures that I have attached the shields to.   A couple of them will need to be rotated and a couple will need to be replaced.   The photos were taken with the macro setting for the camera lens.  I still have some painting to do for the figures.
 
Update
Found a set of a dozen punches that include 3mm and 4mm diameter punches on Ebay for less than $14US with free shipping http://www.ebay.com/itm/380429235433 Rapier has also informed me that they have replaced the faulty mold.  Time to take a look at what additional items I need.